Lifting Supervisor bertanggung jawab memastikan semua pekerjaan yang berkaitan dengan rigging dilakukan dengan aman & efisien
Jakarta | 24 – 28 Agustus 2020 | Rp 9.500.000/ peserta
Jakarta | 21 – 25 September 2020 | Rp 9.500.000/ peserta
Jakarta | 26 – 30 Oktober 2020 | Rp 9.500.000/ peserta
Jakarta | 23 – 27 November 2020 | Rp 9.500.000/ peserta
Jadwal Training 2020 Selanjutnya …
ADVANCED RIGGING TRAINING INTRODUCTION
Lifting Supervisor is in charge of the initial work of erecting the load and to ensure that all rigging work is carried out in a safe and efficient manner, adhering to the regulation and to sound established customs and practices.
The first consideration must at all times, be directed toward the safeguarding life and limb. This consideration must extend to all persons in vicinity or likely to enter the vicinity.
ADVANCED RIGGING TRAINING OBJECTIVE
At the end of course, the participant should be able to:
- Observe general safety first rules and carry out his duties in a safe and responsible manner.
- Have knowledge of safe working load of the crane he is working with.
- Have a full knowledge of hand signal (Australian/ New Zealand Standard)
- Understand the correct type of sling, hook shackle etc. for load.
- Have knowledge of the use of lifting beams, slings and chains.
- Understand the effect of doubling crane hoist rope on safe working.
- Understand use of rope, chain and shackle.
- Understand not to use damaged wire rope or fiber rope, slings or chain where the links are not free or kinked wire rope.
- Understand when slinging a load, pack between sling and load at all point where load has sharp corners, so as to prevent damage to sling.
- Design and apply the knowledge of lifting and lifting plan in their daily work
ADVANCED RIGGING TRAINING OUTLINE
Day 1
- Introduction:
- Definition of Dogger, Slinging & Crane Operator
- Roles & Responsibilities of Rigger:
- Rigger Certification System
- Roles & responsibility of Crane Operator
- Roles & Responsibility of Dogger
- Roles & Responsibility of Slinger
- Roles & Responsibility of Traffic Controller / Flagman
- Roles & Responsibility of Lifting Supervisor
- Accident & Prevention
- Legislative Requirement:
- International Standard: AS/NZS
- Roles and Responsibilities: Crane operator, Crane Owner/End User, Facility/Site Owner, Lift Coordination, Lift Engineer/ Rigging Specialist, Workers and Crane Mechanic
- Hazard And General Safety:
- Outriggers and Crane Stability
- Comparative Soil Bearing Capacities
- Crane Selection Guide
- Electrical Hazard
- Public Road / Pedestrian Hazards
- Utilities Overhead and underground
- Accidents and Lesson learn
- Signalling And Communication:
- Two way Radios
- Conventional Radio
- Trunked Radio
- Radio Direction for Crane Driver
- Bell or Whistle Code
- Hand Signal
Day 2
- Rigging Engineering Calculation
- Determination on Centre of Gravity
- Rectangular Object
- Round or Oval Shape
- Multiple Load / Object
- Rigging Engineering Calculation
- Volume Calculation
- Rectangular Object
- Round or Oval Shape
- Triangle Object
- Cone Object
- Multiple Load/ Object
Ropes & Knots for Rigger (Synthetic & Natural)
- Figure of Eight
- Reef knot
- Single Bowline
- End Splice
- Eye Splice
- Sheet Bend
- Timber Hitch
- Rolling Hitch
- 2 and Half Hitch
- Tagline Hitch
- Clove Hitch
- Etc
- Rigging Engineering Calculation
- Calculation of Mass
Basic Mass Calculation for Various Shapes of Loads Normally Engaged During Crane Operation versus volume
- Concrete/ Cement
- Steel (Mild/ Hard)
- Liquid (Water)
- Wood
- Sand, etc
** Guidelines for Steel pipe, steel bar, Angle Bar, Mild Steel Plate, Mild steel plate bar, C-Channel, Universal Beams, Universal Columns, etc
- Lifting Appliances
- Selection on Sling material
- Sling wire FSWR 1570
- Sling wire FSWR 1770
- Chain Sling GT80 / G100
- Synthetic Webbing (Flat/Round Slings)
- Stacking and Clearances
- Clearance
- Stacking Steel Plate
- Stacking Rolled Steel Coils And Other Round Loads
- Stacking Timber
- Care, Maintenance, and Inspection on Sling Material
- Spreader Bar vs Stabilizer Bar
- Use of Slings / Hoists And Tag line
- Determination of W.L (SWL versus WLL)
- Minimum Breaking Force (MBF) and its usages
Day 3:
- Rigging Engineering Calculation
- Safety Factor requirements
- Lifting Material & Human
- Sling wire FSWR 1570
- Sling wire FSWR 1770
- Chain Sling GT80 / G100
- Synthetic Webbing (Flat/Round Slings)
- ‘choke’ / Hitch Factor
- Rectangular Load
- Round Load
- Sling Angles Factor
- Sudut 30o
- Sudut 45o
- Sudut 60o
- Sudut 90o
- Sudut 120o
- Determination of sling Strength based on diameter & Safety Factor
- Sling Wire
- Synthetic Sling
- Chain Sling
- Determination of Sling length and lifting angle
Day 4:
- Rigging Engineering Calculation
- Inspection of Slings & shackles and attachments
- Sling Wire (5%)
- Chain Sling (5%)
- Synthetic Sling
Note: Determination of acceptance condition of slings and attachments. (Category 1 and Category 2)
- Rigging Engineering Calculation
- Calculation of Multiple Sling
- SWL Sling 1
- SWL Sling 2
- Multiple Crane Lifting / Multiple @ Large Loads
- Tendem Lifting
- Crane Selection and Ordering crane
- Crane type vs Load Chart & Working Radius
- Mobile Crane
- Crawler Crane
- Role & Responsibility of Lifting Supervisor
- Designing Lifting Plan
- Special Lifting (Professional Engineer Interferences): Lifting Specialist in General
Day 5 :
- Practical session on:
- Determination of COG
- Determination of Volume & Mass
- Selection of slings
- Lifting Techniques
- Hand Signaling & Radio Communication
- Inspection of Crane & Lifting Hoist appliances
- Manual Lifting & Mechanical Lifting
- Gin Wheel Application & Limitations
- ASSESSMENT PAPER:
- General Knowledge
- Assessment Legislation
- Assessment Calculation (Lifting Plan)
ADVANCED RIGGING TRAINING INSTRUCTOR
Michael Ferdinand Surjadi
VENUE
Jakarta (Maxone Hotel Menteng, Balairung Hotel Matraman, Sentral Hotel, Haris Tebet, Gd Muamalat Institute, Ibis Manggadua, Little Amaroossa Residence, Cosmo Amaroossa, Zodiak MT. Haryono, Grand Tjokro)
TRAINING DURATION
5 Days
JADWAL TRAINING 2020
- 24 Agust 2020-28 Agust 2020
- 21 Sep 2020-25 Sep 2020
- 26 Okt 2020-30 Okt 2020
- 23 Nop 2020-27 Nop 2020
- 30 Nop 2020-04 Des 2020
INVESTMENT/ PARTICIPANTS
- 9.500.000/ peserta (bayar penuh) atau
- 9.250.000/ peserta (early bird, yang membayar 1 minggu sebelum training) atau
- 8.950.000/ peserta (peserta bergroup yang terdiri dari 3 peserta atau lebih dari 1 perusahaan yang sama)
FACILITIES FOR PARTICIPANTS
- Modul Training
- Flashdisk Training berisi materi training
- Sertifikat
- ATK: NoteBook dan Ballpoint
- T-Shirt
- Ransel
- Foto Training
- Ruang Training dengan fasilitas Full AC dan multimedia
- Makan siang dan 2 kali coffeebreak
- Instruktur yang Qualified
Advanced Rigging