GROUNDING, BONDING, LIGHTNING & SURGE PROTECTION OF ELECTRICAL AND ELECTRONIC SYSTEMS & EQUIPMENT
Bali | 15 – 17 September 2015 | IDR 8.000.000 per participant
Bandung | 15 – 17 September 2015 | IDR 7.000.000 per participant
Yogyakarta | 15 – 17 September 2015 | IDR 6.500.000 per participant
Bali | 21 – 23 September 2015 | IDR 8.000.000 per participant
Bandung | 21 – 23 September 2015 | IDR 7.000.000 per participant
Yogyakarta | 21 – 23 September 2015 | IDR 6.500.000 per participant
Jadwal Training 2015 Selanjutnya …
DESCRIPTION
Few topics generate as much controversy and argument as that of grounding and the associated topics of surge protection, shielding and lightning protection of electrical and electronic systems. Poor grounding practice can be the cause of continual and intermittent difficult-to-diagnose problems in a facility. This workshop looks at these issues from a fresh yet practical perspective and enables you to reduce expensive downtime on your plant and equipment to a minimum by correct application of these principles.
OBJECTIVES
- Apply the various methods of grounding electrical systems
- Detail the applicable national Standards
- Describe the purposes of grounding and bonding
- List the types of systems that cannot be grounded
- Describe what systems can be operated ungrounded
- Correctly shield sensitive communications cables from noise and interference
- Apply practical knowledge of surge and transient protection
- Troubleshoot and fix grounding and surge problems
- Design, install and test an effective grounding system for electronic equipment
- Understand lightning and how to minimize its impact on your facility
- Protect sensitive equipment from lightning
TRAINING OUTLINES
Introduction And Basics
- Fundamentals of grounding
- bonding
- lightning
- surge protection
- shielding
Recommended Design And Installation Practices
- Wiring and grounding for safety and performance
- Wiring and distribution systems
- Dedicated and derived neutral systems
- Grounding and bonding equipment
Fundamentals Of Grounding For Building Electrical Systems
- Grounding of building systems
- Which electrical systems can be operated ungrounded
- Proper methods of grounding building electrical systems
- Location of the service grounding connection
- Proper sizing of grounded (neutral) conductors
Typical Rules To Be Applied
- Rules for multiple services to one building
- Rules for low impedance and high impedance systems
- Rules for bonding requirements at building service equipment
- Grounding electrodes, systems and conductors
- Bonding enclosures and equipment
- Equipment grounding conductor types
- Enclosure and equipment grounding
- Grounding of separately derived systems
Grounding And Noise Control
- Misconceptions of performance grounding
- Single point versus multi point techniques
- Noise and zero signal reference grid
- Avoiding non recommended practices
- Shielding
Electrical Faults
- Ground fault circuit interrupters
- Equipment ground fault protection systems
Applications Of Grounding And Bonding
- Grounding and bonding in hazardous (classified) locations
- Grounding and bonding for health care
- Grounding and bonding for swimming pools, hot tubs and spas
- Static and electricity: grounding and bonding requirements
- Common violations
- Building electrical inspection procedures
- How to recognize hazards
Lightning
- Need for a lightning protection system
- Which protection systems work and which don’t
- Best location for IT equipment
- Optimum grounding for building
- Pitfalls of isolated grounding
- Shielding and bonding of electronics and communications
- Optimum location of surge protection devices
Surge And Transient Protection
- Lightning phenomena
- Protection of power supply
- Protection of electric communications circuits
- Power system faults and switching surges
- Mitigation techniques
- Case studies
Power Conditioning
- Power conditioners
- Uninterruptible power systems
- Power quality alternative sources
INSTRUCTOR
Miftahul Huda, ST., M. Eng.and team
PARTICIPANTS
Instrumentation & Control Engineers, Consulting Engineers, Electrical Engineers, Project Engineers, Maintenance Engineers, Electrical Contractors, Safety Professionals, Consulting Engineers, Electricians, Electrical Inspectors, Power System Protection & Control Engineers, Building Service Designers, Data Systems Planners and Managers, Electrical and Instrumentation Technicians
TIME & VENUE
- 15-17 September 2015
- 21-23 September 2015
- 6-8 Oktober 2015
- 12-14 Oktober 2015
- 20-22 Oktober 2015
- 3-5 November 2015
- 17-19 November 2015
- 24-26 November 2015
- 1-3 Desember 2015
- 8-10 Desember 2015
- 15-17 Desember 2015
- 21-23 Desember 2015
- Hotel Ibis Styles Dagen | Yogyakarta
TRAINING FEE
- IDR 6.500.000 per participant (Non-Residential)
- Minimal participants : 2 persons (Yogyakarta)
- Yogyakarta : Ibis Styles Dagen, Ibis Malioboro, Horison Ultima-Riss, Harper Mangkubumi, 101 Hotel, Grand Tjokro, Novotel, Grand Aston, Phoenix Hotel | Kuota Min. Peserta: 2 orang
- Bali : Ibis Styles Kuta, Ibis Dewi Sri, Ibis Bali Kuta, Ibis Circle Kuta, Harris Hotel | IDR. 8.000.000 Per Peserta (Non-Residential) | Kuota Min. Peserta: 5 orang
- Bandung : De Batara, Amaris, Golden Flower Hotel | IDR. 7.000.000 Per Peserta (Non-Residential) | Kuota Min. Peserta: 5 orang
FACILITIES
- Training Modul
- Stationeries
- Certificate
- Backpack
- Exclusive Polo shirt
- Flashdisk containing materials
- Training photo
- 2x coffee break and lunch
- Transportation Service from airport to hotel / training venue (at least for 2 participants from the same company).