ELECTRICAL AND MECHANICAL ROTATING EQUIPMENT

Electrical and Mechanical Rotating Equipment: Case Study and Problem Shooting

Yogyakarta/ Semarang/ Solo | 27 – 28 Januari 2020 | Rp 6.900.000,-
Bandung/ Jakarta/ Surabaya | 03 – 04 Februari 2020 | Rp 7.900.000,-
Bali/ Batam/ Balikpapan/ Manado | 17 – 18 Februari 2020 | Rp 8.900.000,-
Yogyakarta/ Semarang/ Solo | 02 – 03 Maret 2020 | Rp 6.900.000,-

Jadwal Training 2020 Selanjutnya …

 

 

ELECTRICAL & MECHANICAL ROTATING EQUIPMENT TRAINING OVERVIEW

This course is an integral part of the programme, has a duration of few days, and covers equipment driven directly by gas turbines or indirectly through gas turbine driven generator sets, electrical power systems and motor drivers. Typical applications are for Oil, Gas and other industries

 

ELECTRICAL & MECHANICAL ROTATING EQUIPMENT TRAINING OUTLINES

1. Gas Turbine Engines
   The basic principles underpinning the operation of the gas turbine will be presented. This section will also include a description of the following cycles:- simple, reheat, recuperated, inter-cooled, combined gas and steam and steam injected. The effects of engine rating, variation in efficiencies between engines, maintenance intervals and fuel quality are introduced.
2. Pumps and Compressors
   The basic principles of rotor dynamic and positive displacement pumps and compressors and the effects of cavitation, compressibility, viscosity variation and humidity. Losses in fluid systems and interaction between machines and systems. Introduction to the basic design principles of pumps and compressors, involving shafts, bearings and seal systems. A discussion of the regulation of pumps and compressors. The correct selection and application of pumps and compressors.
3. Electrical Power Systems
   Power System Design covering voltage and frequency control, maximum and minimum system fault levels. A demonstration of power system simulation by computer studies including load flow, voltage drop, short circuit levels, motor starting performance and protection grading.
4. Electrical Power Generation
   An overview of the electrical features of power generation. The mechanical engineer is involved as a member of a design team, often as the lead engineer, with the important requirement of discussing electrical design features with specialist engineers and then being expected to take part in the decision making process for a power generation package. Design, construction and specification of synchronous machines (generators) with typical data sheets.
5. Electric Motors Drive Systems
   Design and construction features of asynchronous machines (motors), load characteristics, active and reactive load sharing, power transfer between power systems. Matching motors to the driven equipment and effect of power supply system variations. Specifications in relation to IEC/BSS standards. Data sheets for the selection and purchase of electrical machines. Electrical Variable Speed Drive Systems with power electronics and various types of convertors, applications to motors and generators, effect on driven equipment. Data sheets for the selection and purchase of systems.
6. Aspects of Electrical Machines
   Hazardous area protection, electrical power three phase calculations with worked examples and typical values that can be used during project evaluations. Operation and Maintenance plans and common failures. Digital microprocessor systems interfacing with plant control systems for the control, protection and retained information on motor performance.
7. Selection of Drivers
   When driving rotating equipment a key aspect of any project is the decision on whether pumps or compressors are to be driven by gas turbine engines or by electric motors from a power system with the option of local gas turbine driven power generation. Each project will always have its own particular solution.

 

Design Workshop

Workshop exercises in which machines are chosen to meet an outline brief for a pump or compressor plant with the appropriate direct or electric motor drive and its control system will be undertaken.

 

Jadwal Training 2020

Hotel Santika Kuta, Bali
Hotel Nagoya Plaza, Batam
Hotel Fave, Balikpapan
Hotel Aston, Manado
Hotel Lombok Raya, Mataram
Hotel Serela Merdeka, Bandung
Hotel Santika Pandegiling, Surabaya
Sofyan Hotel Betawi, Jakarta
Hotel Ibis, Solo
Hotel Ibis Simpang Lima, Semarang
Hotel Ibis Malioboro, Yogyakarta

• 27 – 28 Januari 2020
• 3 – 4 Februari 2020
• 10 – 11 Februari 2020
• 17 – 18 Februari 2020
• 26 – 27 Februari 2020
• 2 – 3 Maret 2020
• 9 – 10 Maret 2020
• 16 – 17 Maret 2020
• 23 – 24 Maret 2020
• 30 – 31 Maret 2020
• 6 – 7 April 2020
• 13 – 14 April 2020
• 20 – 21 April 2020
• 27 – 28 April 2020
• 4 – 5 Mei 2020
• 11 – 12 Mei 2020
• 2 – 3 Juni 2020
• 8 – 9 Juni 2020
• 15 – 16 Juni 2020
• 22 – 23 Juni 2020
• 29 – 30 Juni 2020
• 6 – 7 Juli 2020
• 13 – 14 Juli 2020
• 20 – 21 Juli 2020
• 27 – 28 Juli 2020
• 3 – 4 Agustus 2020
• 10 – 11 Agustus 2020
• 18 – 19 Agustus 2020
• 24 – 25 Agustus 2020
• 31 Agustus 2020 – 1 September 2020
• 7 – 8 Sepember 2020
• 14 – 15 September 2020
• 21 – 22 September 2020
• 28 – 29 September 2020
• 5 – 6 Oktober 2020
• 12 – 13 Oktober 2020
• 19 – 20 Oktober 2020
• 26 – 27 Oktober 2020
• 2 – 3 November 2020
• 9 – 10 November 2020
• 16 – 17 November 2020
• 23 – 24 November 2020
• 30 November 2020 – 1 Desember 2020
• 7 – 8 Desember 2020
• 14 – 15 Desember 2020
• 21 – 22 Desember 2020
• 28 – 29 Desember 2020

 

Tugino, ST., MT

 

ELECTRICAL AND MECHANICAL ROTATING EQUIPMENT: CASE STUDY AND PROBLEM SHOOTING

Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training

1. INFORMATION OPTIONS
2. Judul Training(required)
3. Tanggal Training
4. Select a message type Registration Offering Letter (Permintaan Proposal Penawaran) Next Schedule Information (Jadwal selanjutnya) More Information (Informasi tambahan) Others (lain-lain) (required)
5. PERSONAL DATA
6. Your Name(required)
7. Job Title(required)
8. Company(required)
9. Company Address
10. Email(valid email required)
11. Mobile Phone(required)
12. Office Phone(required)
13. Extention No.
14. Facsimile (Fax)
15. Website
16. PRE REGISTRATION DATA (Tidak Mengikat)
17. Penanggung Jawab Training di Perusahaan
18. Email
19. Office Phone+Ext atau No. Handphone
20. Jumlah Peserta(required)
21. Nama-nama peserta
22. Payment Method Bank Transfers Submitting an Invoice Cheque or Cash on arrival ( If Possible)
23. MESSAGE FOR TRAINING PROVIDER
24. Pesan untuk penyelenggara Training
25. CC this registration / message to me
26. Isikan angka/huruf pada gambar

 

cforms contact form by delicious:days